Urine Drug Test Multi 7-Panel
€14.24
A drug test that detects traces of 7 substances in urine.
This test is specially developed to detect certain pill-based drugs, but also to trace the most common substances.
Our Multi 7-Panel Drug Test is easy to use and provides results within minutes.
This test is specially developed to detect certain pill-based drugs, but also to trace the most common substances.
Our Multi 7-Panel Drug Test is easy to use and provides results within minutes.
- Secure payment by card and PayPal
- Fast delivery
Orders received before 2:00 p.m. are shipped the same day. Shipped 100% discreetly, with no logos or markings revealing the contents.
- BrandSafecare
Description
Article no.: 111033
This urine test detects 7 commonly used drugs. A multi-test is useful if you are unsure of what drugs the test person uses and abuses. The test works by dipping a test stick into a cup of collected urine and reading the result on the test device.
Cut-off:
Oxyc. (OXY) 100 ng/mL
Propoxifeno (PPX) 300 ng/mL
Tram. (TML) 100 ng/mL
Opiá. (OPI) 2000 ng/mL
Fent.(FYL) 200 ng/mL
Bupr. (BUP) 10 ng/mL
Metamp. (MET) 1000 ng/mL
Procedure
1. Remove the test panel from the foil pouch.
2. Pull off the protective sleeve to expose the aspirator.
3. Collect urine in a clean, dry container and directly dip the absorbent end of the test stick vertically into it. Leave in the urine for about 10-15 seconds. NOTE! Do not allow the urine to pass over the "arrow" mark on the test device.
4. Remove the test device from the urine and place it on a smooth, dry surface. Start the timer and read the result within 5 minutes. NOTE! Do not read the result after 10 minutes.
Interpretation of results:
NEGATIVE:* Two lines appear. One red line should be in the control region (C), and one to
adjacent obvious red or pink line should be in the test region (T). This negative result
indicates that the drug concentration is below detectable level.
*NOTE: The shade of red color in the test region (T) may vary, but the test should be considered
negative if it is even a faint pink line.
POSITIVE: A red line appears in the control region (C). No line appears in the test region
(T). This positive result indicates that the drug concentration is above the detectable level.
ERROR: The control line does not appear. Insufficient sample volume or incorrect execution are
the most likely reasons for the control line not appearing. Review the procedure and
repeat the test with a new test strip. If the problem persists, discontinue the procedure and contact
your local supplier.
The test is CE marked.
Cut-off:
Oxyc. (OXY) 100 ng/mL
Propoxifeno (PPX) 300 ng/mL
Tram. (TML) 100 ng/mL
Opiá. (OPI) 2000 ng/mL
Fent.(FYL) 200 ng/mL
Bupr. (BUP) 10 ng/mL
Metamp. (MET) 1000 ng/mL
Procedure
1. Remove the test panel from the foil pouch.
2. Pull off the protective sleeve to expose the aspirator.
3. Collect urine in a clean, dry container and directly dip the absorbent end of the test stick vertically into it. Leave in the urine for about 10-15 seconds. NOTE! Do not allow the urine to pass over the "arrow" mark on the test device.
4. Remove the test device from the urine and place it on a smooth, dry surface. Start the timer and read the result within 5 minutes. NOTE! Do not read the result after 10 minutes.
Interpretation of results:
NEGATIVE:* Two lines appear. One red line should be in the control region (C), and one to
adjacent obvious red or pink line should be in the test region (T). This negative result
indicates that the drug concentration is below detectable level.
*NOTE: The shade of red color in the test region (T) may vary, but the test should be considered
negative if it is even a faint pink line.
POSITIVE: A red line appears in the control region (C). No line appears in the test region
(T). This positive result indicates that the drug concentration is above the detectable level.
ERROR: The control line does not appear. Insufficient sample volume or incorrect execution are
the most likely reasons for the control line not appearing. Review the procedure and
repeat the test with a new test strip. If the problem persists, discontinue the procedure and contact
your local supplier.
The test is CE marked.